EH5700 SERIES ENCLOSURE

March 27, 2020 posted by

The EH Series can be used in? Not all agency approvals apply to all models. Connect an 8-inch Cam Cam Track Flex coupler. Only the tautness of the drive shaft assembly holds the flange bearing in place. There are two different More information.

Box Saco, ME. Please read this guide thoroughly. On all models except the EH57 and EH, reinstall the circuit board. Ten percent is generally the maximum allowable voltage drop for AC-powered devices. The Ignitor is designed for More information. Global Water Instrumentation, Inc. Please read this owner s Manual carefully before operating the unit.

The forward-opening lid allows for maximum accessibility during installation and when camera and lens adjustments are necessary. Replace the plastic cover enclosire the power supply on the circuit board. Please follow all local, state and national.

Pelco EH Enclosure Environmental VAC

In no event will Pelco be liable for any special, incidental, or consequential damages including loss of use, loss of profit, and claims of third parties however caused, whether by the negligence of Pelco or otherwise. Go to Pelco s web site at ftp: Failure to do so can result in serious injury. All models feature an adjustable camera sled with a built-in elevation block that can be removed and inverted. Advanced Introduction 2 Hours Purpose This technical bulletin.

Details of the defect or problem If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Remove the latch on the side of the enclosure where the wiper shaft is located. This document is hosted by Old Will Knott Scales www. All pan and tilts, scanners, or preset lenses used in continuous motion applications preset scan, tour, and auto scan modes. Wire the wiper assembly to power as follows: Please read this manual thoroughly prior to equipment set-up, operation. Sanford, North Carolina 8 A. Remove the plastic cover from the power supply section of the circuit board in front of the fan plate.

  PROJECT METALBEAST PLOT

The EH Series enclosures are available with a full complement of accessories which include blower, heater, window defroster, sun shroud, window wiper, preset lens wiring harness, VAC outlet, and thermal insulation. This manual must be read and.

Remote Faucet Pump System. Video heads will be covered for a period of six months.

Pelco EH5700 User Manual

Hook the rear of enclosuee circuit board mounting over the screw installed at the top of the enclosure s rear panel. Slide the support bracket onto the wiper shaft. The potentiometer only makes one revolution. All goods requiring warranty repair shall be sent freight prepaid to a Pelco designated location. Turn off power to the enclosure. Please read this guide thoroughly.

Maximum Maximum Table Height: Write the product s. Follow all More information. Before assembling your Buyers ladder rack it s important to read, understand, and follow all listed instructions. If desired, the latches can be secured with a padlock of suitable size for additional security. Installation and eh5700 should only be done by qualified service personnel and conform to all local codes.

  SPARTACUS VENGEANCE CAST SEPPIA

WW57 Series Window Wiper Kit for EH5700 Series and EH5700L Legacy Series Enclosures

Failure to do so can result. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. To use this website, you must agree to our Privacy Policyincluding cookie policy.

The main printed More information. Ten percent is generally the maximum allowable voltage drop for AC-powered devices.

The Ignitor is designed for. Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the sreies use or application made of the Products.

The enclosure opens from the rear. Please follow ebclosure local, state and national More information. Please enclosute this manual thoroughly prior to equipment set-up, operation More information. The lamp and color wheel will be covered for a period of 90 days.

Refer to Figure for steps through 5. Refer to Figure 6 and slip the flex coupler over the drive shaft.

Attach the bottom right and bottom left sides of the fan plate to the camera sled track with screws and lock washers.

A01 Copyright Dell, Inc.